绘制曲线工具列
To open a toolbar...
Arc
Draw an arc with options for center, start, angle, and direction.
链接至圆弧工具列
圆弧, 起点,终点,起点方向
以起点、终点、起点的方向建立圆弧。
圆弧, 起点,起点方向,终点
以起点、起点的方向、终点建立圆弧。
圆弧, 起点,终点,通过点
以起点、终点、通过点建立圆弧。
圆弧, 起点,通过点,终点
以起点，圆弧上一点以及终点建立圆弧。
圆弧，与数条曲线相切
建立与数条曲线正切的圆弧。
圆弧, 正切、正切、半径
以正切、正切、半径建立圆弧。
Cancel
Cancel the current command and deselects objects.
Cancel,All
Turns off Points, CurvatureGraph, EMap, Zebra, MoveUVN, CurvatureAnalysis, and deselects objects.
Catenary
Creates a curve that a hanging chain or cable assumes under its own weight when supported only at its ends.
Circle
Draw a circle from center and radius, diameter, points on the circumference, and circumference length.
链接至圆形工具列
圆, 直径
以中心点与直径建立圆。
圆, 正切、正切、半径
建立与两条曲线正切的某个半径的圆。
圆, 与工作平面垂直: 中心点、半径
从中心点、半径建立与工作平面垂直的圆。
Curve
Draw a curve from control point locations.
链接至 曲线工具列
CurveThroughPt
Fit a curve through point objects.
Ellipse
Draw a closed elliptical curve from focus points, center and edges, bounding rectangle, and around a curve.
链接至 椭圆工具列
椭圆, 直径
以中心点与直径建立一个椭圆。
Explode
Break objects down into components.
ExtractSrf
Separates or duplicates polysurface, Extrusion, or SubD faces.
HandleCurve
Draw chained Bézier curves with editing handles.
Helix
Draw a helical curve with options for number of turns, pitch, vertical, reverse, and around a curve.
弹簧线, 垂直
建立一条与工作平面垂直的弹簧线。
InterpCrv
Fit a curve through picked locations.
HandleCurve
通过控制杆绘制贝塞尔曲线。
InterpCrvOnSrf
Fit a curve through locations on a surface.
Join
Connect curves, surface edges, or surfaces to form a single object.
Line
Draw a single line segment.
直线, 与曲线垂直
建立一条起点与其它曲线垂直的直线。
直线, 至曲线上的垂直点
建立一条终点与其它曲线垂直的直线。
直线, 与曲线正切
建立一条起点与其它曲线正切的直线。
Parabola
Draw a parabolic curve from focus and vertex or endpoint.
Parabola3Pt
Draw a parabolic curve through three picked points.
Polygon
Draw a polygon with a specified number of sides with options for inscribed/circumscribed, by edge, star-shaped, around a curve, and vertical.
进入多边形工具列
多边形, 正方形 (从中心点、角)
以中心点与一个角建立一个正方形。
多边形, 正方形 (从边)
以一个边建立一个正方形。
多边形, 星形
建立一个星形的多边形。
Polyline
Draw a multi-segment polyline with options for line and arc segments, tracking line helpers, and close.
进入直线工具列
Lines
Draw multiple adjoining line segments.
Rectangle
Draw a rectangular closed polyline from with options for starting at the center, three points, vertical, and rounded with arc or conic corners.
进入矩形工具列
矩形, 三点
指定三个点建立一个矩形。
矩形, 圆角
建立一个四个角为圆弧的矩形。
矩形, 圆角 (圆锥角)
建立一个四个角为圆锥线的矩形。
矩形, 垂直
建立一个与工作平面垂直的矩形。
Split
Divide objects using other objects as cutters.
Split,Isocurve
Divide objects using isocurves as cutters.
